|
| MOQ: | 100 set |
| Price: | Negotiable |
| Standard Packaging: | Packing according to customer requirements |
| Payment Method: | T/T |
Excessive loading: When the material is loaded too much and exceeds the rated capacity of the equipment, it will affect the drying efficiency of the material and cause additional burden on the motor, reducer and other components. The solution is to load according to the rated capacity of the equipment and ensure that the material density is within the appropriate range. During operation, check the loading situation frequently to ensure that it is not excessive.
Vacuum is too low or too high: Vacuum is too low or too high will have an adverse effect on the drying effect and quality of the material. The solution is to check the vacuum system regularly to ensure good sealing and no leakage, and pay attention to the temperature of hot water or steam to ensure that it is within the appropriate range. During use, regular maintenance and maintenance should be carried out to ensure the normal operation of the equipment.
The outer layer of the cylinder liner falls off: Improper use of the equipment or inadequate maintenance may cause damage to the glass-lined liner. The solution is to choose a suitable dryer according to the nature of the material to avoid damage caused by improper use. At the same time, regular inspections and maintenance should be carried out to promptly detect and repair damaged parts.
Excessive air flow during "venting": During the venting process, if the air flow is too large, it will impact the vacuum system and cause equipment damage. The solution is to use an exhaust valve to control the flow during venting to avoid excessive airflow. A pressure reducing valve can be added to control the flow of air to reduce the impact of positive and negative airflows.
Excessive noise: It may be caused by loose foundation, damage to the reducer or bearing, etc. The solution is to regularly check and tighten the foundation bolts to ensure the stability of the equipment. At the same time, regular inspections of components such as reducers and bearings should be carried out, damaged components should be replaced in time, and lubricating oil should be added to increase their service life.
Leakage at the inlet and outlet: Leakage at the inlet and outlet may be caused by sticking or damage to the sealing strip. The solution is to clean the material on the surface of the inlet and outlet and replace the damaged sealing strip. The state of the sealing strip should be checked regularly to promptly detect and repair leakage problems.
|
|
| MOQ: | 100 set |
| Price: | Negotiable |
| Standard Packaging: | Packing according to customer requirements |
| Payment Method: | T/T |
Excessive loading: When the material is loaded too much and exceeds the rated capacity of the equipment, it will affect the drying efficiency of the material and cause additional burden on the motor, reducer and other components. The solution is to load according to the rated capacity of the equipment and ensure that the material density is within the appropriate range. During operation, check the loading situation frequently to ensure that it is not excessive.
Vacuum is too low or too high: Vacuum is too low or too high will have an adverse effect on the drying effect and quality of the material. The solution is to check the vacuum system regularly to ensure good sealing and no leakage, and pay attention to the temperature of hot water or steam to ensure that it is within the appropriate range. During use, regular maintenance and maintenance should be carried out to ensure the normal operation of the equipment.
The outer layer of the cylinder liner falls off: Improper use of the equipment or inadequate maintenance may cause damage to the glass-lined liner. The solution is to choose a suitable dryer according to the nature of the material to avoid damage caused by improper use. At the same time, regular inspections and maintenance should be carried out to promptly detect and repair damaged parts.
Excessive air flow during "venting": During the venting process, if the air flow is too large, it will impact the vacuum system and cause equipment damage. The solution is to use an exhaust valve to control the flow during venting to avoid excessive airflow. A pressure reducing valve can be added to control the flow of air to reduce the impact of positive and negative airflows.
Excessive noise: It may be caused by loose foundation, damage to the reducer or bearing, etc. The solution is to regularly check and tighten the foundation bolts to ensure the stability of the equipment. At the same time, regular inspections of components such as reducers and bearings should be carried out, damaged components should be replaced in time, and lubricating oil should be added to increase their service life.
Leakage at the inlet and outlet: Leakage at the inlet and outlet may be caused by sticking or damage to the sealing strip. The solution is to clean the material on the surface of the inlet and outlet and replace the damaged sealing strip. The state of the sealing strip should be checked regularly to promptly detect and repair leakage problems.
